MDPE Piping System

Overview

Sangir manufactures MDPE Pipe Fittings per national and international norms: ISO 4427; DIN 8074; EN 1220; IS 4984; IS 14151; IS 14333. Depending on customer requirements, Sangir manufactures its lines from different grades; however, it specializes in PE100 pipes from composite black raw materials. MDPE Pipes100 is considered the strongest of all PE grades for piping and has a maximum nominal bore for the same pressure rating as PE 80/63. According to international standard ISO 4427, an MDPE Piping System material can be certified as PE100 only if it passes 10,000 hours Long Term Hydrostatic Strength (LTHS) test for 50 years to show that it has an MRP of over 10 MPa for a lifetime of a minimum of 50 years.

Features
Pipes
Fittings
Technical Information

PROPERTIES OF PRODUCT STANDARD Data Unit
DENSITYISO – 1183 / ASTM 1505> 0.930g/cc
MELT FLOW RATE (190°c/5 kg)ISO – 1133 / ASTM D 1238<1.4g/10min
HARDNESS ( SHORE-D)ASTM D 2240> 50Shore-D
TENSILE STRENGTH @ YIELDISO – 527 / ASTM D 638 Type-IV≥ 15Mpa
ELONGATION @ BREAKISO – 527 / ASTM D 638 Type-IV≥ 350%
IMPACT STRENGTHDIN 8078/ ISO 179NO BREAKKJ/M2
HYDRO STATIC STRENGTH(800C,4.5Mpa Hoop stress,165 Hrs)DIN EN ISO 1167NO LEAK NOR BURST
LONGITUDINAL HEAT REVERSION(1100C)DIN EN ISO 2505< 3%

 

Video

HDPE Pipes as per ISO 4427 PE63

Standards

  • IS 4984:2016
  • IS 14333:
  • ISO 4427
  • DIN 8074
  • AZ4130

  

Product Range

  • 16-1200mm OD / max PN25
All dimensions are in mm

Download Dimensions

  • Suitable for underground pipes through the adjustment to local ground movement.
  • Impact-resistant and tough
  • Thermal resistant Application possible between -40°C & 80°C.
  • Smooth internal wall Low blockage risk due to low deposit/residue effects
  • Application in open-air unrestricted through coloring with carbon black.
  • Lower cost due to relatively long life.
  • Non-conductive.
  • Suitable for the transport of polluted waste water.
  • No condensation is possible during short periods of cooling.
  • Easy installation using butt-welding and electro-fusion techniques.
  • Environmental friendly.
  • Homogeneous welded joints – Pull tight and leakproof.
  • Prefabrication – Fast and cost-saving installation.
  • Light in weight – Cost saving in transport and handling.
Featured List of Applications
  • Municipal
  • Industrial
  • Marine / Dredging
  • Agriculture
  • Electrical ( Cable Ducting)
  • Infrastructure
  • Geothermal Heating
  • Culverts
  • Float Docks

HDPE Pipes as per ISO4427 PE 80

Standards

  • IS 4984:2016
  • IS 14333:
  • ISO 4427
  • DIN 8074
  • AZ4130

  

Product Range

  • 20-1200mm OD / max PN25
All dimensions are in mm

Download Dimensions

  • Suitable for underground pipes through the adjustment to local ground movement.
  • Impact-resistant and tough
  • Thermal resistant Application possible between -40°C & 80°C.
  • Smooth internal wall Low blockage risk due to low deposit/residue effects
  • Application in open-air unrestricted through coloring with carbon black.
  • Lower cost due to relatively long life.
  • Non-conductive.
  • Suitable for the transport of polluted waste water.
  • No condensation is possible during short periods of cooling.
  • Easy installation using butt-welding and electro-fusion techniques.
  • Environmental friendly.
  • Homogeneous welded joints – Pull tight and leakproof.
  • Prefabrication – Fast and cost-saving installation.
  • Light in weight – Cost saving in transport and handling.
Featured List of Applications
  • Municipal
  • Industrial
  • Marine / Dredging
  • Agriculture
  • Electrical ( Cable Ducting)
  • Infrastructure
  • Geothermal Heating
  • Culverts
  • Float Docks

Search for Sangir Products

Moulded Bend 90⁰

Moulded bend 90⁰

Standards

  • Design: DIN 16963/Manufacturers Standard
  • MOC: HDPE
  • Pressure-Temperature Rating: Up to PN 10 (SDR11)
  • End Preparation: Plain Ends
  • Test Method: DIN 16963

  

Range

  • 20-225mm OD / max PN20

  

All dimensions are in mm

Download Dimensions

  • Suitable for underground pipes through the adjustment to local ground movement.
  • Impact-resistant and tough
  • Thermal resistant Application possible between -40°C & 80°C.
  • Smooth internal wall Low blockage risk due to low deposit/residue effects
  • Application in open-air unrestricted through coloring with carbon black.
  • Lower cost due to relatively long life.
  • Non-conductive.
  • Suitable for the transport of polluted waste water.
  • No condensation is possible during short periods of cooling.
  • Easy installation using butt-welding and electro-fusion techniques.
  • Environmental friendly.
  • Homogeneous welded joints – Pull tight and leakproof.
  • Prefabrication – Fast and cost-saving installation.
  • Light in weight – Cost saving in transport and handling.
Featured List of Applications
  • Municipal
  • Industrial
  • Marine / Dredging
  • Agriculture
  • Electrical ( Cable Ducting)
  • Infrastructure
  • Geothermal Heating
  • Culverts
  • Float Docks

Moulded Tee 90° Butt Fusion

Moulded Tee 90

Standards

  • Design: DIN 16963
  • MOC: HDPE
  • Pressure-Temperature Rating: Up to PN 10 (SDR11)
  • End Preparation: Plain Ends
  • Test Method: DIN 16963

  

Range

  • 20-225mm OD / max PN20
All dimensions are in mm

Download Dimensions

  • Suitable for underground pipes through the adjustment to local ground movement.
  • Impact-resistant and tough
  • Thermal resistant Application possible between -40°C & 80°C.
  • Smooth internal wall Low blockage risk due to low deposit/residue effects
  • Application in open-air unrestricted through coloring with carbon black.
  • Lower cost due to relatively long life.
  • Non-conductive.
  • Suitable for the transport of polluted waste water.
  • No condensation is possible during short periods of cooling.
  • Easy installation using butt-welding and electro-fusion techniques.
  • Environmental friendly.
  • Homogeneous welded joints – Pull tight and leakproof.
  • Prefabrication – Fast and cost-saving installation.
  • Light in weight – Cost saving in transport and handling.
Featured List of Applications
  • Municipal
  • Industrial
  • Marine / Dredging
  • Agriculture
  • Electrical ( Cable Ducting)
  • Infrastructure
  • Geothermal Heating
  • Culverts
  • Float Docks

Stubend Adaptor-Long Neck

Butt fusion long neck stubend

Standards

  • Design: DIN 16963
  • MOC: HDPE
  • Pressure-Temperature Rating: Up to PN 10 (SDR11)
  • End Preparation: Plain Ends
  • Test Method: DIN 16963

  

Range

  • 20-1200mm OD / max PN20
All dimensions are in mm

Download Dimensions

  • Suitable for underground pipes through the adjustment to local ground movement.
  • Impact-resistant and tough
  • Thermal resistant Application possible between -40°C & 80°C.
  • Smooth internal wall Low blockage risk due to low deposit/residue effects
  • Application in open-air unrestricted through coloring with carbon black.
  • Lower cost due to relatively long life.
  • Non-conductive.
  • Suitable for the transport of polluted waste water.
  • No condensation is possible during short periods of cooling.
  • Easy installation using butt-welding and electro-fusion techniques.
  • Environmental friendly.
  • Homogeneous welded joints – Pull tight and leakproof.
  • Prefabrication – Fast and cost-saving installation.
  • Light in weight – Cost saving in transport and handling.
Featured List of Applications
  • Municipal
  • Industrial
  • Marine / Dredging
  • Agriculture
  • Electrical ( Cable Ducting)
  • Infrastructure
  • Geothermal Heating
  • Culverts
  • Float Docks

Stubend Adaptor-Long Spigot

Butt-fusion-long spigot stubend

Standards

  • Design: DIN 16963 PART-4
  • MOC: HDPE (PE100)
  • Pressure-Temperature Rating: Up to PN 16 (SDR11)
  • End Preparation: Plain Ends
  • Test Method: DIN 16963 PART-4/IS 4984 /IS14333/ISO 4427

  

Range

  • 20-1200mm OD / max PN20
All dimensions are in mm

Download Dimensions

  • Suitable for underground pipes through the adjustment to local ground movement.
  • Impact-resistant and tough
  • Thermal resistant Application possible between -40°C & 80°C.
  • Smooth internal wall Low blockage risk due to low deposit/residue effects
  • Application in open-air unrestricted through coloring with carbon black.
  • Lower cost due to relatively long life.
  • Non-conductive.
  • Suitable for the transport of polluted waste water.
  • No condensation is possible during short periods of cooling.
  • Easy installation using butt-welding and electro-fusion techniques.
  • Environmental friendly.
  • Homogeneous welded joints – Pull tight and leakproof.
  • Prefabrication – Fast and cost-saving installation.
  • Light in weight – Cost saving in transport and handling.
Featured List of Applications
  • Municipal
  • Industrial
  • Marine / Dredging
  • Agriculture
  • Electrical ( Cable Ducting)
  • Infrastructure
  • Geothermal Heating
  • Culverts
  • Float Docks

Moulded End Cap

Moulded End cap

Standards

  • Design: Manufacturers Standard
  • MOC: HDPE
  • Pressure-Temperature Rating: Up to PN 10 (SDR11)
  • End Preparation: Plain Ends
  • Test Method: DIN 16963/ IS 8008 / IS 8008 / ISO 4427 / SPPL STD

Range

  • 20-1000mm OD / max PN20